Engineering superior dissolved oxygen transfer rates (SOTR) through precision transmission technology. Designed for the rigorous demands of British trout farms and global fisheries.
Overview: Engineering Resilience for Continuous Duty Cycles
In the intensive aquaculture sector, specifically within the United Kingdom’s cold-water trout and salmon fisheries, the Paddlewheel Aerator is not merely an accessory; it is the life-support system of the biomass. The gearbox situated at the physical center of these machines performs a critical tri-functional role: supporting the electric motor, managing massive torque multiplication, and absorbing the violent reaction forces generated by impellers slapping the water surface.
EVER-POWER has re-engineered the traditional aerator gearbox to address the “Fatal Three” failure modes observed in North Sea and inland UK operations: Seal failure due to bio-fouling, thermal runaway during summer 24/7 cycles, and micro-pitting from oscillating shock loads. Our drive units convert high-speed motor input (typically 1400 RPM) into the hydrodynamic sweet spot of 80–120 RPM, ensuring optimal water splash and oxygen transfer without cavitation.
Technical Specification Matrix: EVER-POWER Series 900-Aqua
| 매개변수 설명 | 사양 값 | Engineering Standard / Note |
|---|---|---|
| 정격 전력 입력 | 1.5 kW – 3.0 kW (2HP – 4HP) | IEC Standard Motors |
| 감소율 | 14:1 / 16:1 / 20:1 | 맞춤 설정 가능 |
| 출력 토크(공칭) | 450 Nm – 850 Nm | AGMA Class II Service Factor |
| 최대 충격 토크 | 1800 Nm | Startup/Blockage condition |
| 입력 속도(최대) | 1800 RPM | 50Hz/60Hz Compatible |
| 주택 자재 | Cast Iron HT250 / Ductile Iron QT450 | ASTM A48 / A536 |
| 기어형 | Bevel-Helical or Double Worm | Precision Ground |
| 기어 소재 | 20CrMnTi 합금강 | 침탄 및 담금질 |
| 표면 경도(기어) | 58-62 HRC | Depth 0.8-1.2mm |
| 능률 | > 92% (Bevel) / > 75% (Worm) | Tested at full load |
| 윤활 유형 | 스플래시 윤활 | 오일 배스 |
| Recommended Oil | Synthetic ISO VG 320 | Mobil SHC 632 or equiv. |
| 오일 용량 | 1.8 L – 2.5 L | Depends on mounting pos. |
| 밀봉재 | Double Lip FKM (Viton) | High Temp / Salinity Resist |
| 입력축 직경 | 19mm / 24mm / 28mm | Keyed (DIN 6885) |
| 출력축 직경 | 35mm / 40mm / 50mm | H6 Tolerance |
| 베어링 브랜드 | C&U / SKF / NSK | 테이퍼 롤러 베어링 |
| 베어링 L10 수명 | 25,000시간 이상 | 연속 근무 |
| 소음 수준 | 1m 거리에서 < 75 dB(A) | 저소음 프로파일 |
| 작동 온도 | -20°C ~ +90°C | Case Temperature |
| 침투 보호 | IP65 | Dust & Water Jet Tight |
| 페인트 코팅 | 에폭시 프라이머 + 폴리우레탄 | 염수 분무 시험 > 500시간 |
| 부식 등급 | C4 (ISO 12944) | Marine/Coastal Areas |
| 진동 속도 | < 2.8 mm/s | RMS Value |
| 무게(건조 중량) | 22 kg – 35 kg | Excluding Motor |
| 장착 패턴 | Universal 4-Bolt Flange | Interchangeable |
| 통풍구 | Pressure Compensating | Prevents seal blowout |
| 백래시 | Standard (10-20 arcmin) | Precision Available |
| 샤프트 재질 | 40Cr (AISI 5140) | 유도 경화 |
Anatomy of a Paddlewheel Gearbox
Positioning: The gearbox sits atop the floating pontoon structure, acting as the structural bridge between the high-revving electric motor and the slow-turning impeller shaft. It is subjected to constant cyclic loading caused by the paddles entering and exiting the water.
작동 원리: Through a two-stage reduction (typically a bevel gear set followed by a helical set, or a double worm gear configuration), it multiplies the motor’s torque by a factor of 14 to 20. This allows a relatively small 2HP motor to drive large 8-paddle impellers against the significant resistance of water.
Adaptation to Extreme Scenarios
- Salinity Corrosion: In brackish water shrimp farms, standard casings rust in weeks. We use electrophoretic coating (E-coating) on cast iron to prevent oxidation.
- Start-up Shock: When algae blooms thicken water viscosity, startup torque spikes. Our gears feature a “Case-Hardened Core” to absorb shock without teeth snapping.
- UV Exposure: Plastic components like oil caps are UV-stabilized to prevent brittleness under the intense sun of open ponds.
[United Kingdom] Regulatory Landscape & Field Conditions
🇬🇧 UKCA & Safety Compliance
Post-Brexit, agricultural machinery components entering the Great Britain market must adhere to the 기계 공급(안전) 규정 2008. EVER-POWER gearboxes are fully compliant with UKCA standards, ensuring valid technical files are available for importers. We also align with BS EN ISO 4254-1 for agricultural machinery safety, specifically regarding guarding of moving parts (PTO connections) and noise emission levels.
🌧️ Terrain & Crop Specifics
Scotland & Highlands: For Atlantic Salmon hatcheries using freshwater lochs, water ingress is the primary enemy. Our “Highland Edition” gearboxes feature IP66 seals to withstand heavy rainfall and constant splashing.
이스트 앵글리아 및 펜스 지역: In lowland fisheries and irrigation reservoirs, dissolved oxygen drops critically in summer. Gearboxes here must run 24/7. We utilize high-grade synthetic oils to maintain viscosity stability during these heatwaves.
Design Philosophy: The “Zero-Leak” Imperative
“When we designed the Gen-3 Aqua Box, our primary constraint wasn’t just torque—it was environmental protection. In a fish farm, an oil leak isn’t just a maintenance issue; it’s an ecological disaster that kills the stock. We moved away from standard NBR seals to double-lipped SKF Viton seals running on a polished stainless steel wear sleeve. This separates the harsh pond water from the internal lubricant. Furthermore, we optimized the thermal dissipation fins using CFD (Computational Fluid Dynamics) to ensure the gearbox runs 15°C cooler than market averages, extending seal life significantly.”
— Chief Engineer, Drivetrain Division, EVER-POWER
Global Success Stories: Solving Real Pain Points
위치: Hampshire, UK (Trout Fishery)
문제점: “Our neighbors complained about the whining noise from the aerators at night. The council threatened to shut us down.”
에버파워 솔루션: “We replaced the straight bevel gears with precision-ground 스파이럴 베벨 기어. The sliding contact of the spiral teeth reduced noise emissions by 8 decibels, bringing the farm back into compliance with local noise ordinances.”
위치: Mekong Delta, Vietnam (Shrimp Farming)
문제점: “Saltwater corrosion was eating through the gearbox housing every 6 months.”
에버파워 솔루션: “We introduced our ‘Marine Spec’ housing with a 3-layer epoxy coating and 316 Stainless Steel output shafts. Lifespan increased to 3+ years in hyper-saline conditions.”
위치: Mato Grosso, Brazil (Tilapia)
문제점: “Overheating. The ambient temp is 38°C, and the boxes were cooking the oil.”
에버파워 솔루션: “We increased the oil sump capacity by 20% and added external cooling ribs. We also switched them to a high-viscosity synthetic lubricant.”
범용 호환성 및 교체 가이드
우리의 기어박스 are designed with standardized mounting footprints to serve as drop-in replacements for major global brands. Whether you are running equipment in the UK, Netherlands, or Italy, our units fit seamlessly.
호환 가능한 대체품:
- Comer Industries (Series D / N)
- Bonfiglioli (Worm Series)
- SITI Gearboxes
- Local Taiwanese Aerator Brands
완벽한 구동계 솔루션
Select Heavy-Duty Planetary Gear Drive Units for Rotary Milking Parlors
회전식 착유 시설용 고하중 유성 기어 구동 장치
In the high-throughput dairy landscape of the United Kingdom—from the pasture-based herds of the South West to the intensive units in Cheshire—the rotary milking parlor is the cornerstone of efficiency.
자동 분뇨 제거 로봇용 고토크 DC 기어 모터: 영국 낙농 표준
In the automated dairy management sector, specifically for Automatic Manure Scraping Robots, the propulsion system is the single most critical failure point.
⚠️ When to Replace Your Aerator Gearbox?
Watch for these 4 distinct signs of imminent failure to prevent oxygen crashes:
- 유화유: If the oil looks like “milky coffee,” the water seal has failed. Immediate replacement is needed to save the gears.
- 과도한 반발: Rotate the impeller by hand. If there is more than 15 degrees of “play” before the motor shaft moves, the worm gear is worn out.
- Hot Spots: If the casing temperature exceeds 80°C (cannot touch by hand) under normal load, internal friction is critical.
- Rhythmic Knocking: Indicates a damaged bearing race or broken tooth on the pinion.
자주 묻는 질문 (B2B)
Do you ship gearboxes compliant with UK import standards?
Yes, absolutely. All our agricultural gearboxes destined for Great Britain carry the UKCA mark and include the necessary Declaration of Conformity to clear customs smoothly.
Can I retrofit your gearbox onto an Italian-made aerator frame?
In 95% of cases, yes. We utilize standard ISO mounting flange dimensions. If you provide the bolt pattern and shaft size, we can confirm the match instantly.
What is the lead time for a container load to Southampton?
For standard models, production takes 25-30 days. Shipping to Southampton or Felixstowe typically adds 30-35 days. We recommend ordering 2 months pre-season.
Do you offer customized ratios for high-density shrimp farming?
Yes, we can adjust the gear ratio to 16:1 or higher to increase torque for deeper ponds or 4-impeller setups often used in intensive farming.
How do you handle warranty claims for international buyers?
We offer a 12-month warranty. For international B2B clients, we typically provide a percentage of free spare parts (seals/bearings) or replace defective units in the next shipment.
What oil should I use for UK winter operations?
For UK winters, especially in Scotland, we recommend a lower viscosity synthetic oil like ISO VG 220 to ensure smooth startups in near-freezing temperatures.
gzl님이 편집함
