Engineered for the UK Fishing Fleet
Designed to withstand the corrosive salinity of the North Sea and the brutal shock loads of Cornish crab potting. The ultimate self-locking transmission solution for hydraulic haulers, complying with MCA safety standards and exceeding OEM fatigue life by 40%.
1. The Heart of the Hauler: Why Worm Gear is Non-Negotiable
In the commercial fishing sector, particularly within the potting fisheries of the South West UK (Cornwall, Devon) and the heavy trawling grounds off Scotland, the Net Hauler және Pot Hauler are critical safety components. They are not merely winches; they are the lifeline that retrieves tons of biomass from the seabed.
The defining characteristic of the Ever-power marine gearbox for this application is the Self-Locking Mechanism. When a hydraulic motor stops—either intentionally or due to a hose burst—the gearbox must instantly hold the load. A standard helical gear would back-drive, causing the heavy net or line of pots to plummet back into the depths, endangering crew limbs and risking vessel stability. Our worm gear sets, specifically designed with a lead angle typically below 5 degrees for high-ratio units, provide static self-locking coefficients that exceed industry safety norms.
Engineer’s Note: The “Back-Driving” Hazard
“I recall a retrofit project in Grimsby where a skipper had installed a cheap planetary reducer on a pot hauler to save costs. The moment the hydraulic pressure dipped during a stall, the pots ran back, nearly taking a deckhand’s arm. We replaced it with our Series-W worm unit. The friction inherent in the sliding contact of the bronze wheel against the steel worm creates a natural brake. It’s physics acting as a safety device.”
Application Matrix
- Target Equipment:
Hydraulic Pot Haulers, Net Haulers, Capstans. - Vessel Types:
Inshore Creelers (<10m), Stern Trawlers, Scallop Dredgers. - Installation Position:
Vertical (Output shaft up) or Horizontal deck mount. - Primary Drive:
Hydraulic Motor (Danfoss/Parker type orbit motors).
2. Technical Specifications: Marine Series
The following data reflects the precise engineering standards of our exported units for the UK market. Parameters are optimized for high-torque, low-speed hauling operations.
| Параметр санаты | Техникалық құндылық / Стандарт | Инженерлік ескертпе |
|---|---|---|
| Номиналды айналу моменті сыйымдылығы | 450 Nm – 3,200 Nm | Scalable based on hauler tonnage (1.5T to 5T) |
| Азайту коэффициенті | 15:1-ден 60:1-ге дейін | Optimized for hydraulic motor speeds of 300-900 RPM |
| Worm Shaft Material | 20CrMnTi қорытпасынан жасалған болат | 58-62 HRC дейін көміртекті және сөндірілген |
| Құрт дөңгелегінің материалы | Nickel Aluminum Bronze (CuAl10Ni5Fe4) | Spec ASTM B148 C95500 – Critical for salt corrosion resistance |
| Корпус материалы | Cast Iron GG25 / Ductile GGG40 | Shot blasted + Zinc-rich primer |
| Кіріс интерфейсі | SAE A / SAE B гидравликалық фланец | Direct mount for orbit motors (Danfoss OMP/OMR) |
| Шығыс білігі | Stainless Steel 316L (Optional) | Standard C45 with Chrome plating available |
| Service Factor (f.s.) | > 2.0 @ Heavy Shock Load | Designed for “Class III” shock loading (snagged nets) |
| Тиімділік (статикалық) | 55% – 70% | Deliberately moderate to ensure self-locking |
| Майлау түрі | Synthetic Polyglycol (PAG) VG320 | Extended life, anti-foaming for rocking motion |
| Май тығыздағышының бренді | SKF / TTO (қос ерін) | Viton material for temp resistance |
| Басып кіруден қорғау | IP66 / IP67 | Washdown ready, resistant to high-pressure hose |
| Бояу жабыны | ISO 12944 C5-M (Marine) | 3-layer epoxy system, 320 microns DFT |
| Working Temp | -20°C-тан +80°C-қа дейін | Includes cold start capability for North Sea winter |
| Мойынтіректердің қызмет ету мерзімі (L10h) | > 15 000 сағат | Oversized tapered roller bearings |
| Output Shaft Load (Radial) | Up to 25,000 N | Critical for cantilevered sheave loads |
| Output Shaft Load (Axial) | Up to 12,000 N | Handles pull-in forces |
| Кері соққы | Standard 0.15 – 0.25 mm | Reduced backlash not required for hauling |
| Діріл деңгейі | < 4,5 мм/с (RMS) | Class B balance quality |
| Тыныс алу клапаны | Spring-loaded Marine Vent | Prevents water ingress during cooling |
| Орнату бағыты | Universal (B3, B5, B14, V1, V5) | Sealed for all-position use |
| Шу деңгейі | < 75 dB @ 1 meter | Important for small wheelhouses |
| Hollow Shaft Option | Available (Keyed or Splined) | For compact deck designs |
| Коррозия сынағы | Salt Spray ASTM B117 > 500h | Validated housing coating |
| Салмақ | 15 kg – 85 kg | Dependent on frame size (40 to 155) |
| Мұнай сыйымдылығы | 0.4L – 3.5L | Pre-filled at factory optional |
| Жылулық рейтингі | P_therm > P_mech | Oversized casing for heat dissipation |
| Кілт жолы стандарты | DIN 6885 / BS 4235 | Compatible with UK imperial shafts if requested |
| Сертификаттау | CE, UKCA, ISO 9001:2015 | Full documentation provided |
| Кепілдік | 18 ай | Standard is 12, we offer extended for marine |
From the Dockside: Engineer’s Field Notes
Case Study 1: The Scallop Dredger Retrofit (Fraserburgh, UK)
Ever-power Engineer: “I noticed the standard seals were running directly against the cast iron hub which had rusted. We switched you to our ‘Cassette Seal’ system where the seal runs on a hardened stainless steel sleeve, and added a secondary V-ring to fling off the grit.”
Нәтиже: The vessel ‘Highlander’ has run for 24 months without a single gearbox leak. Maintenance costs dropped by £2,400 annually.
Case Study 2: The Pot Hauler Space Constraint (Cornwall, UK)
Ever-power Engineer: “We utilized our compact NMRV-Power series with a direct hydraulic motor mount (SAE A). This eliminated the bell housing adapter, shortening the drive assembly by 120mm.”
Нәтиже: Skipper James reclaimed valuable deck space, improving ergonomics and safety during 14-hour shifts.
Case Study 3: The North Sea Trawler (Urk, Netherlands)
Ever-power Engineer: “Using our digital reverse-engineering database, we identified the footprint as a match for our WP-DS 135 series. We shipped a unit with a custom output flange within 4 days.”
Нәтиже: Minimal downtime. The vessel met its quota for the herring season.
Market Comparison & Compatibility
Ever-power беріліс қораптары are engineered to be dimensional drop-in replacements for major European brands, but with internal upgrades suited for the aftermarket reality.
| Функция | Ever-power Marine Series | Standard European Brand | Жалпы эконом бренді |
|---|---|---|---|
| Дөңгелек материалы | Ni-Al Bronze (C95500) | Phosphor Bronze | Brass / Standard Bronze |
| Shaft Coating | Ceramic or Hard Chrome | Standard Steel | Black Oxide |
| Кепілдік | 18 ай | 12 ай | 3-6 Months |
*Disclaimer: Ever-power is an independent manufacturer. References to other manufacturers’ names, trademarks (e.g., Bonfiglioli, Motovario, Spencer Carter) are solely for identification and compatibility purposes. Our parts are not original OEM parts but are designed to fit and perform as high-quality replacements.
Толық трансмиссиялық шешімдер
We don’t just sell the box. We supply the link.
PTO Shafts & Hydraulics
For tractor-driven haulers, we supply Қуат беру біліктері with wide-angle joints and shear bolt limiters. For hydraulic systems, we offer the matching Bell Housings және Jaw Couplings to connect your Danfoss or Parker motor to the gearbox input.
- ✔ Stainless Steel Sheaves (Custom cast)
- ✔ Hydraulic Motors (OMP/OMR Types)
- ✔ Mounting Brackets for Gunwale fixing
Жиі қойылатын сұрақтар
How do I stop my pot hauler gearbox from leaking oil in rough seas?
Leaks often occur due to pressure buildup. Ensure you are using a spring-loaded breather valve, not a fixed plug. Also, check if your seals are compatible with the synthetic oil used; we recommend Viton seals for marine haulers.
Can I replace a Spencer Carter hauler gearbox with an Ever-power unit?
Yes. While we are not the OEM, our WP and NMRV series are manufactured with standard metric flanges and shaft sizes that often match these haulers directly. Please send us the nameplate data for verification.
What is the best gear oil for fishing winches in the UK winter?
For UK conditions (approx -5°C to 20°C), a fully synthetic Polyglycol (PAG) oil with ISO VG 320 viscosity is ideal. It maintains flow in cold mornings but won’t thin out under heavy load.
Why is my worm gear overheating during long hauling sessions?
Overheating implies low efficiency or overload. Check if the oil level is correct (half-sight glass). If you upgraded your hydraulic pump for more speed, you might be exceeding the gearbox’s thermal input limit.
Ready to Upgrade Your Deck Machinery?
Don’t let a failed gearbox cost you a catch. Contact Ever-power today for marine-grade replacements delivered to the UK.
